View HR34B-12WLPD-10S_4577778.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
NEW
Push-on Bayonet Lock Miniature Waterproof Connector
HR34B Series
Push-on Bayonet Lock
Mating : Just inserting plug unit will complete mating
Un-mating : Rotating sleeve to unlock mating
fig.1
sFeatures
1. Water and dust protection
* IP67 water and dust protection rating when fully mated. * Resistant to industrial grade oils. * 4-position receptacles are sealed against water penetration when mounted on the panel - no protective cap is required.
Cable exit directions
45
2. Easy and precise mating
* Mating: Just inserting plug unit completes mating Unmating: Rotating sleeve counterclockwise unlocks connectors (fig.1) * Marking helps align plug with receptacle when mating. * 3 guide keys make blind mating possible. (Receptacle structure prevents plug from damaging receptacle terminals)
fig.2
3. Multi-directional cable exit
Right angle plugs allow the cable to exit in 8 directions, in 45 increments.(fig.2)
4. Safty standards
The 4-position connectors meet requirements of T UV standard.
5. Wide variation
Item Number of positions Connector type Terminations(plug) Terminations(receptacle) Conduit material Applicable cable size 4,10 straight plug,right angle plug,receptacle solder,crimp panel mount through-hole,wire solder plastic,metal O5.3~7.3, O6.5~8.0, O8.0~9.0(under development)
2010.52
1
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. HR34B SeriesqPush-on Bayonet Lock Miniature Waterproof Connector
sSpecifications
Current rating Ratings Voltage rating 10 pos.: 3 A 4 pos. : 5 A 10 pos.: 200 V AC, 250 V DC 4 pos. : 200 V AC, 200 V DC (contamination level 3) 400 V AC, 400 V DC (contamination level 2) Specification 30 mo max. 1,000 Mo min. No flashover or insulation breakdown No electrical discontinuity of 10 s or longer No electrical discontinuity of 10 s or longer Contact resistance: 30 mo max. Operating temperature range -25C to 125C
Storage temperature range
-25C to 85C
Item 1.Contact resistance 2.Insulation resistance 3.Withstanding voltage 4.Vibration
Conditions 1 A DC 500 V DC 10 pos. : 900 V AC / 1 minute 4 pos. : 2,000 V AC / 1 minute Frequency: 10 to 500 Hz/cycle, total amplitude of 0.75 mm, 98m/s2 each, 3 hours in 3 axis. Acceleration of 490 m/s2, 11 ms duration, 3 axis, each for 3 hours 500 cycles Temperature :-55C / +15 to +35C / +85C / +15 to +35C Time :-30 min. / 10 to 15 min. / 30 min. / 10 to 15 min. 5 cycles 336 hours at 71C, and humidity of 95%
5.Shock
6.Durability (Mating / un-mating) 7.Temperature cycle
Insulation resistance: 500 Mo min.
8.Humidity 9.Water protection
Insulation resistance: 50 Mo min. (at high humidity) Insulation resistance: 500 Mo min. (when dry)
No water penetration when submerged for 48 hours at the depth of 1.8 meters.
sMaterials
qPlugs
Part Outer shell Insulator Female contacts O-ring Gasket 10 pos. 4 pos. Material Zinc alloy, aluminum alloy, and polyamide resin (black) PPS Phosphor bronze Copper alloy Fluororubber, Nitrile hydride rubber Finish Black chrome plating, black chromate finish (Cr +3) Color: Black Gold plated Silver plated --------------Remarks --------------UL94V-0 -------------------------------------------
qReceptacles
Part Outer shell Insulator Male contacts Ground contact O-ring 10 pos. 4 pos. 10 pos. 4 pos. Material Zinc alloy PPS Copper alloy Brass Brass Fluororubber Finish Black chromate finish (Cr +3) Color: Black Gold plated Silver plated Gold plated Silver plated --------------Remarks --------------UL94V-0 -----------------------------------------------------------------------
2
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. HR34B SeriesqPush-on Bayonet Lock Miniature Waterproof Connector
sOrdering information
qPlugs
HR34B - 12 WP A - 10 S - X ( ** )
1 1 Series name 2 Shell size 3 Shell style 2 3 4 5 6 7 8
(Excluding ground contacts) : HR34B Series : Diameter(mm) of the mating interface of the plug WP : Straight plug WLP : Right-angle plug 4 Conduit material and Applicable cable size A:Conduit material metal, Applicable cable O5.3~7.3 B:Conduit material metal, Applicable cable O6.5~8.0 D:Conduit material plastic, Applicable cable O5.7~7.3 E:Conduit material plastic, Applicable cable O6.5~8.0 K:Conduit material metal, Applicable cable O8.0~9.0(under development)
5 Number of contact : Number of contacts. 6 Contact type
S : Female wire solder SC : Female crimp
7 Keying
Blank : Standard X : X key position 8 Other specifications : 2 numerical digits wil be added when there is a specifications change other than shown in positions q to u
qReceptacles
HR34B - 12 WR A - 10 P - X ( ** )
1 1 2 3 4 2 3 4 5 6 7 8
(Excluding ground contacts) Series name : HR34B Series Shell size : Diameter(mm) of the mating interface of the plug Shell style WR : Receptacl Shell type Blank : Rectangular flange type for 10 positions A : Square flange for 10 positions B : Square flange for 4 positions
5 Number of contact : Number of contacts. 6 Contact type
P : Male,wire solder PD : Male,through hole contact
7 Keying
Blank : Standard X : X key position 8 Other specifications : 2 numerical digits wil be added when there is a specification change other than shown in positions q to u
qCrimp contacts
HR34B - SC1 - 2 1 1
1 2 3 4 5 4 Conductor size : AWG#20 - 25 5 Plating
1:Gold plated
1 Series name : HR34B Series 2 Contact style : SC1:Female contact 3 Contact type
1 : 100pcs.per bag 2 : 10,000pcs per reel
3
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. HR34B SeriesqPush-on Bayonet Lock Miniature Waterproof Connector
sStraight plugs
qStandard type (Conduit material :Plastic)
49
O19
xWire solder
Part Number HR34B-12WPD-10S HR34B-12WPE-10S HR34B-12WPD-4S HR34B-12WPD-4S-X HR34B-12WPE-4S HR34B-12WPE-4S-X HRS No. 134-0026-0-00 134-0027-2-00 134-0020-3-00 134-0023-1-00 134-0025-7-00 134-0031-0-00 O8.5 O6.5~8.0 A O7.4 O8.5 O7.4 Applicable cable diameter range O5.7~7.3 O6.5~8.0 O5.7~7.3
All dimensions: mm Solder cup inner diameter O1
O1.7
xCrimp (separate contacts required)
Part Number HR34B-12WPD-10SC HR34B-12WPE-10SC HRS No. 134-0037-6-00 134-0038-9-00 A O7.4 O8.5 Applicable cable diameter range O5.7~7.3 O6.5~8.0
qRobust type(Conduit material :Metal) xWire solder
Part Number HR34B-12WPA-10S(71) HR34B-12WPB-10S(71) HR34B-12WPK-10S HRS No. 134-0004-7-71 134-0007-5-71 Under development A O7.4 O8.5 O9.5 Applicable cable diameter range O5.7~7.3 O6.5~8.0 O8.0~9.0 O1 All dimensions: mm Solder cup inner diameter
qCrimp (separate contacts required)
Part Number HR34B-12WPA-10SC HR34B-12WPB-10SC HR34B-12WPK-10SC HRS No. 134-0017-9-00 134-0028-5-00 Under development A O7.4 O8.5 O9.5 Applicable cable diameter range O5.7~7.3 O6.5~8.0 O8.0~9.0
Not all cables of applicable dia. range can be easily assembled. Please kindly check with factory before use.
4
A
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. HR34B SeriesqPush-on Bayonet Lock Miniature Waterproof Connector
sRight angle plugs
qStandard type (Conduit material : Plastic)
33.5
O19
xWire solder
Part Number HR34B-12WLPD-10S HR34B-12WLPE-10S HR34B-12WLPD-4S HR34B-12WLPD-4S-X HR34B-12WLPE-4S HR34B-12WLPE-4S-X HRS No. 134-0039-1-00 134-0040-0-00 134-0030-7-00 134-0034-8-00 134-0035-0-00 134-0036-3-00 O8.5 O6.5~8.0 A O7.4 O8.5 O7.4 30.85 B Applicable cable diameter range O5.7~7.3 O6.5~8.0 O5.7~7.3
A
B
All dimensions: mm Solder cup inner diameter O1
O1.7
xCrimp (separate contacts required)
Part Number HR34B-12WLPD-10SC HR34B-12WLPE-10SC HRS No. 134-0041-3-00 134-0042-6-00 A O7.4 O8.5 B 30.85 Applicable cable diameter range O5.7~7.3 O6.5~8.0
qRobust type (Conduit material :Metal) xWire solder
Part Number HR34B-12WLPA-10S(71) HR34B-12WLPB-10S(71) HR34B-12WLPK-10S HRS No. 134-0005-0-71 134-0008-8-71 Under development A O7.4 O8.5 O9.5 31.5 B 30.5 Applicable cable diameter range O5.7~7.3 O6.5~8.0 O8.0~9.0 O1 All dimensions: mm Solder cup inner diameter
qCrimp (separate contacts required)
Part Number HR34B-12WLPA-10SC HR34B-12WLPB-10SC HR34B-12WLPK-10SC HRS No. 134-0018-1-00 134-0029-8-00 Under development A O7.4 O8.5 O9.5 31.5 B 30.5 Applicable cable diameter range O5.7~7.3 O6.5~8.0 O8.0~9.0
Not all cables of applicable dia. range can be easily assembled. Please kindly check with factory before use.
5
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. HR34B SeriesqPush-on Bayonet Lock Miniature Waterproof Connector
sReceptacles
xWire solder
48) 2. (R
1 3 7
4-O
3.2
B A
4
8
10
A B
All dimensions: mm Part Number HR34B-12WRA-10P HR34B-12WRB-4P HR34B-12WRB-4P-X HRS No. 134-0016-6-00 134-0021-6-00 134-0024-4-00 A 17.26 18.26 B 23.4 25.4 Solder cup inner diameter O1 O1.3
O ring for water proof is not attached. Please find appropriate one from the market.
xThrough hole
3.3
5.8
8.55
20 13.4
2
3.2 4-O
Part Number HR34B-12WR-10PD(71)
HRS No. 134-0003-4-71
O ring for water proof is not attached. Please find appropriate one from the market.
sCrimp contacts
xFemale
15
1.2
Part Number HR34B-SC1-111 HR34B-SC1-211
CL No. 134-0051-7-00 134-0050-1-00
Packaging 100 pcs. per bag 10,000 pcs. per reel
Applicable conductor AWG #20 - 25 (Stranded wire)
Note: Use wire with a jacket diameter of 1.7mm max.
6
32.4
39
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. HR34B SeriesqPush-on Bayonet Lock Miniature Waterproof Connector
sConnector Mating Combinations
10 pos. Plugs
Straight, Wire Solder or Crimp (Standard key position) HR34B-12WPA-10S,10SC HR34B-12WPB-10S,10SC HR34B-12WPD-10S,10SC HR34B-12WPE-10S,10SC HR34B-12WPK-10S,10SC
10 pos. Receptacles
Through hole HR34B-12WR-10PD
Right angle, Wire Solder or Crimp (Standard key position) HR34B-12WLPA-10S,10SC HR34B-12WLPB-10S,10SC HR34B-12WLPD-10S,10SC HR34B-12WLPE-10S,10SC HR34B-12WLPK-10S,10SC
Wire Solder HR34B-12WRA-10P
4 pos. Plugs
Straight, Wire Solder (Standard key position) HR34B-12WPD-4S HR34B-12WPE-4S Standard polarizing key
4 pos. Receptacles
Wire solder (Standard key position) HR34B-12WRB-4P
Right angle, Wire Solder (Standard key position) HR34B-12WLPD-4S HR34B-12WLPE-4S
Standard key position
Straight, Wire Solder (X key position) HR34B-12WPD-4S-X HR34B-12WPE-4S-X Wire solder (X key position) HR34B-12WRB-4P-X
Right angle, Wire Solder (X key position) HR34B-12WLPD-4S-X HR34B-12WLPE-4S-X
X key position
X key position
7
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. HR34B SeriesqPush-on Bayonet Lock Miniature Waterproof Connector
sApplicable tools
Description Manual contact crimping tool Press Applicator Contact extraction tool Part Number HT304/HR34B-1 CM-105 AP105-HR34B-1 RP6-SC-TP CL No. 150-0107-9 901-0005-4 901-2051-2 150-0039-0 HR34B-SC1-111 HR34B-SC1-211 Applicable contact HR34B-SC1-111 HR34B-SC1-211 Applicable cable AWG20,AWG23,AWG25 AWG20 to AWG25
---------------
qManual contact crimping tool
qPress CM-105 (Applicator ordered separate)
qContact extraction tool
sIllustrations of mated connectors.
Right-angle plug Mating Combinations 10 pos. plug shell A,B type. Plug + receptacle through-hole Plug + receptacle wire solder Plug + receptacle through-hole Plug + receptacle wire solder Plug + receptacle through-hole Plug + receptacle wire solder A 31.0 31.5 31.3 31.8 32.0 32.5 31.3
10 pos. plug shell D,E type.
10 pos. plug shell K type.
(33.5)
4 pos.plug + receptacle wire solder
B A
Straight plug Mating combinations 10 pos.plug + receptacle through-hole 10 pos.plug + receptacle wire solder 4 pos.plug + receptacle wire solder
B 49.6 50.1 49.6
8
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. HR34B SeriesqPush-on Bayonet Lock Miniature Waterproof Connector
BRecommended panel cutouts
qReceptacle - wire solder
4-B
All dimensions: mm HR34B-12WRA-10P HR34B-12WRB-4P HR34B-12WRB-4P-X 18.260.05 M30.5 1 0/-0.1 12.5 +0.1/0 17 +0.1/0 1.1 0/-0.1 16.3 +0.1/0 20.8 +0.1/0
A
A B C
A
17.260.05
D E
C
Recommended O ring dia. Part Number
OD OE
Cross-section 1.5 1.5
diameter 11.5 15.5
HR34B-12WRA-10P HR34B-12WRB-4P HR34B-12WRB-4P-X
qReceptacle - through hole
O-ring (Not supplied, cross-section diameter 1.78 , inner diameter 20.35) (13.4)
4(R 5. 2)
All dimensions: mm
(2.3)(xxx)
(22.4)
(1.3)
4-M30.5
(13.4) (18)
(13.6)
Outline of the O-ring
Notes 1: The receptacle panel cutout shows the view from the mating side of the connector.
BPCB mounting pattern
qReceptacle - Through hole
2.15 2.4 17 0 3 4.4 2.15
1 0. +0
(32.4)
All dimensions: mm
in al )
7
O1
10
5.5
1
3
4
8
.9 +0.1
2.4
Alignment mark
1.4
+0 .0 05
0
-O0
(Po
siti
10
1.2 3.6
2-O
1.2 3.6
(G
0
r
n ou
d
te
rm
oni
ng
pos
t) N
ote
3
Note 1: The contact configuration shows the view from the mating side. Note 2: Tolerance of 0.05 mm is recommended for the plated through hole location and diameter. Note 3: Not a plated-through holes.
9
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. HR34B SeriesqPush-on Bayonet Lock Miniature Waterproof Connector
BReceptacle Contact Arrangement
4 pos.wire solder 10 pos.wire solder 10 pos.through hole
1 2 3 4
1 5 8
2 6 9
3 7 10 4
1 5 8
2 6 9
3 7 10
note.1 View direction:Mating surface of pin insert. note.2 mark is ground terminal.
BHandling
1. Mating 2. Un-mating
Receptacle Plug Locking collar B
A Rotate counter-clockwise Mating position alignment marks
Holding the plug by the outer shell (A) align the arrow on the plug with the alignment mark on the receptacle and push straight in.
Rotate the locking collar counter-clockwise to a full stop and unmate the plug from the receptacle.
BPrecautions
Center line of the connector
When completely mated and locked the alignment arrow on the plug must line-up with the center line of the connector (alignment mark on the receptacle).
Alignment mark
If the alignment arrow and the center line of the connectors are not aligned (1 mm max.) re-insert the plug until they are aligned.
1 mm max.
1. When disconnecting or inserting the connector, be sure to do so after turning off the power. 2. To insert the connector, push it in until the arrow tip of the plug mating mark indicates the specified position of the diagram below (i.e., the mating mark of the receptacle). 3. Note that the display method of the mating mark will differ depending on the receptacle. 4. To maintain the waterproof quality and cable clamp force, use a cable that is within the range of the applicable cable diameter. 5. Please consult Hirose Electric Sales for harness assembly procedure.
10

▲Up To Search▲

Price & Availability of HR34B-12WLPD-10S

	To Download HR34B-12WLPD-10S Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .